1.Introduction to Keynote Speeches on ICACMVE'2011
2.Numerical Simulation Research on Hydraulic Stewart Force Feedback Manipulator
3.Motion Simulation Based on Virtual Reality
4.Research on the Closed Hydraulic Regeneration System of the Boom Potential Energy in Hybrid Excavators
5.Design a New Type of Double-Parallel Platform Road Simulation System
6.Design of a Novel Vehicle Active Suspension and Its Simulation Research
7.Special Vehicle Driving Simulator with Motion Presence
8.Research on Servo Controller of Hydraulic Excavator Dynamic Simulation Test System Based on System on Chip
9.Research on Control Strategy for Active Suspension Based on Inertial Control Theory
10.A Fast Forward Kinematics Algorithm for 3-RPS Parallel Mechanism
11.The Integration Re-Design of Construction Machinery Hydraulic Components
12.Research on Working Characteristics for the Steel Ropes of Large Ship-Unloader's Hoisting Mechanism
13.Dynamical Analysis and Structural Optimization of Pulling Arm of the Hook-Lift Compressed Rubbish Truck
14.Dynamic Load Analysis of Excavator Main Pumps Based on Stochastic Theory
15.Multidisciplinary Optimization of Mixing Blades Based on Parameter Sensitivity Analysis
16.An Engineering Method for Asphalt Foaming Modelling Integrating Gas-Liquid Phase Change Process
17.An Engineering Method for Parameter Sensitivity Analysis of Asphalt Foaming
18.The Foaming Chamber Design and Evaluation Based on the Analysis of Bitumen Foaming Essential Characteristics
19.Master-Slave Control for Construction Robot Teleoperation-An Improved Variable-Gain Velocity Control with Force Feedback
20.The Selection of the Dozer-Determination of Optimal Parameters of the Bulldozer for Specified Work Conditions
21.Machinery in Information Oriented Construction in Japan
22.Modeling and Analysis of Hydraulic Pile Hammer System
23.Fluid-Solid-Heat Coupling Analysis of the Problem of Hydraulic Slide Catching
24.Loading Capacity Analysis of a 3-SPS-S Mechanism for Segment Assembly Robots in Shield Tunnelling Machines
25.Research on Power Control System in Various Operating Conditions for Loader
26.A Study of Point Disposal for a Sort of Heterogeneous Cylinder Series Levelling Mechanism and Optimum Design
27.The Theory Analysis of Double Spiral Rotary Hydraulic Motor Basing on Virtual Work Principle
28.Dynamic Characteristic Analysis of Walking Mechanism of Roadheader
29.A Dynamic Pressure Simulation of Electro-Hydraulic Proportional Variable Pump Based on AMESim
30.Dynamic Optimization Design Research of Truck Mounted Pump Boom Based on Concrete Flowing Impact
31.Heat Balance Mechanism Analysis in the Hydraulic System of Concrete Pump
32.Application of Topology Optimization in Lightweight Design of Concrete Pump-Truck Booms
33.Optimization Design of Backhoe Hydraulic Excavator Working Device Based on Feasible Digging Area
34.Research on the Influence of the Ratio of Normal and Tangential Digging Resistance on the Stability against Leaning orward of Backhoe Hydraulic Excavator
35.Strength Analysis of Working Device of Hydraulic Excavator Based on VB and ANSYS
36.CMAC and PID Compound Control of Twin-Spool System
37.The Theory of Determining Damage Location of Steel Towers
38.Force Analysis of Connecting Rod between Separate Transportation Vehicles
39.Fault Diagnosis of TTW30 Excavator/Loader Hydraulic Driving System
40.Dynamics Analysis of Compactor Based on Rigid-Flexible Coupling Model
41.Grader Service Life Estimation Based on Load Spectrum
42.Modeling and Strength Analysis of Blade Circle Frame Used in Grader Working Device
43.Estimation Method of New Bulldozer Load Spectrum Based on Similar Structure
44.Tower Crane Good Condition Diagnosis System Development
45.Analysis of Hydraulic System of 250 Tons Tripod Jack Test Stand
46.Dynanuc Response Analysis of Vehicles and Low Frame Bridge System Based on Multi-Body Dynamics
47.The Research and Development of an Intelligent and Rapid Design System for Ship Loader
48.Following Control Research on Booms of Concrete Pump Vehicles
49.Discussion on the Opportunity for Skid Steer Loader's Development under the Background of Aging Society in China
50.Discussion Debugging Analysis about Directional-Control-Valve on YC50-8 Excavator
51.Design Expert System of Hydraulic Excavator Using Relevant Matrix for Knowledge Representation
52.The Technical Scheme and Advantage of Full-Electro-Hydraulic Proportional Control Excavator
53.Several Key Issues on Design and Development of Tyre Roller
54.Ultracapacitor-Based Auxiliary Energy System for Construction Machinery
55.Analysis and Improvement of Heavy-Duty Test Equipment Based on ANSYS
56.The Research and Application of Load Sensing Hydraulic System on Construction Machinery
57.Study on Electronic Braking Force Distribution Control Strategy of the Tractor-Semitrailer Vehicle
58.Application of Time-Domain System Identification Techniques for Crane Structure Based on Output-Only Measurement
59.An Indirect Free-Interface Component Mode Synthesis Technique
60.Vibratory Mixing and the Improvement of Concrete Performance
61.Study on the Load Sensing and Control Strategy of Hybrid Wheel Loader
62.Bulldozer Ripper Co-Simulation Based on ADAMS and SimHydraulics
63.Dynamics Research on Driving Shaft of Heavy Load Multi-Body System
64.Matching Calculations and Co-Simulation Based on Elevated Sprocket Bulldozer Powertrain
65.Comparison on the White Light and the Laser Inline Measurement Technique in the Dimension Control of Car Body
66.Transient Performance Analysis of a Thermo-Electric Generator Installed in EGR Path of a Diesel Engine
67.Spark Ignition Strategies for Extending Combustion Limits of Diluted Charge for Modern Engines
68.Investigation of the Spray Morphology and Breakup of Diesel/Biodiesel Blends Using Ultrafast X-Ray Imaging
69.Digitallntegration Processing of Diesel Cylinder Head Vibration Acceleration Signal with Multiple Moving Average Method to Eliminating Trend
70.The Analysis of Noise and Vibration in Drum Brake Systems of Vehicles Based on Numerical Analysis
71.Simulation Analysis on Flexible Multibody Dynamics of Drum Brake System of a Vehicle
72.Adaptive Electronic Differential Control Technology of Wheel Electric Driving System
73.Study on Temperature-Field Test of Combination Piston for a Certain Type of Diesel Engine
74.Static Stress Analysis of a Diesel's Connecting Rod by Experiment and Simulation
75.Probe into a New Type of Wind Resistance Brake Mechanism
76.Numerical Simulation on the Working Process of High Power Diesel Engine in Plateau Area
77.The Choice of Working Medium in Low-and-Medium Temperature Cogeneration Technology and the Effect to System
78.Influence of Geometry Parameters on the Section Distortion of Thin-Walled Rectangular Tube during Rotary Bending
79.Development and Analysis of Automotive Electronic Standards
80.Design and Analysis of the Performance Testing Equipment for Automobile Steering Meshing Pair
81.Design of LIN Bus Data Logger Based on 8-Bit MCU
82.Psychoacoustic Analysis of the Noise of Air Supply System on Fuel Cell Vehicles
83.New Method in Analysis Manufacture Symmetry on Inner Structure of Multi-Hole Nozzle
84.Analysis of Air Fuel Ratio and Combustion Characteristics of GDI Engines at Cold Start Condition
85.In-Cycle Misfire Control on a GDI-HCCI Engine Employing Ion Sensing Technology
86.Research Progress of Thermal Management of Li-Ion Batteries in Electric Vehicles Using Phase Change Materials
87.Research of Wind Cooling Technology for Electric Vehicle Li-Ion Battery Pack
88.Design Optimization of Electro-Hydraulic Actuation System of Variable Nozzle Turbocharger (VNT)
89.Engine Exhaust Manifolds Durability Analysis
90.Real-World Gaseous and Ultrafine Particle Emission Characteristics of an Euro Ⅳ Diesel Bus
91.A Test Method for Automotive Door Glass Motion Deviation
92.Review of Battery's Charging and Discharging Efficiency
93.Thermal Simulation and Test of Lithium-Ion Battery for Electric Vehicle
94.Fluid Power Transmission Characteristics of Aviation Kerosene
95.Analysis of Attitude Control Method of Flight Machine Based on Gas-Jet Side Force
96.New HST Makes Easy Utilization of Ocean Wave Energy
97.Research on Spiral Strip Suppression Effects on Vortex-Induced Vibration of Water Riser Pipe Based on Numerical Wave Tank
98.Application of I2C Bus in Embedded Simulation System of Electric Propulsion System
99.A High-Precision Positioning Approach for GPS in Bulk Ports by Using Kalman Filter with Pre-Calculated Factors
100.Data Mining Technology and its Application in Air Cargo Business
101.License Plate Character Neural Network Recognition Based on Wavelet and GA Optimization
102.Studies on the Inertial Effect in Fluid Transport Using a Simplified Porous Media Model
103.Experimental and Numerical Studies on the Suppression of Vortex Induced Vibrations Using Helical Strakes
104.A Novel Yard Allocation Approach for Expofl Containers in Container Terminal
105.Working Process Visualization of Bucket Wheel Stacker
106.Construction of Container Terminal Distributed Cooperation Virtual Environment
107.The Tendency Research of Modern Engineering Logistics and Equipment Technology
108.Research on CAN-Based Control System for Dynamic Compaction Machine
109.Calculation and Simulation Study on Temperature Field of Dry Dual-Clutch's Friction Plate
110.Study on Vibration Reduction and Design of Dual Mass Flywheel
111.Application of Risk-Based Maintenance Approach in Automated Storage and Retrieval System
112.The Holistic Capability Evaluation of Military Construction Machinery on the Base of AHP
113.Research on Collaborative Design Workflow System of Complex Products in Construction Machinery
114.Application of Top-Down Method in 55ZJC Type Shield Hauler
115.Research of Intelligent Fault Diagnosis for Hydraulic System of Cranes Outriggers
116.Study of the Crane Comprehensive Evaluation Index Syste
117.Tamping Machine Fault Diagnosis Based on Fuzzy Inference
118.Application and Scheme Comparison of CCHP System in Huanghua Airport
119.Fault Diagnosis of Bearing Based on Integration of Nonlinear Geometry Invariants
120.Research and Application of Engineering View Generation Based on Secondary Development of SolidWorks
121.7.5 Meters Aerial Work Platform Mechanics Performance Analysis under Typical Working Cases
122.Wheel-Rail Contact Analysis of Vehicles in a Low-Frame-Bridge System in Quay
123.Study on Time-Variation Dynamics Model for Gearbox with Gear Crack Fault
124.Steady-State Thermal Equilibrium Analysis to the Transfer Case of Heavy Vehicle Based on ANSYS
125.Robotic GMAW Surfacing Remanufacturing Forming for Construction Machinery Parts
126.Hydraulic Motor Fault Tracing Based on Casting Quality
127.Working Fluid Selection for the Organic Rankine Cycle in Slag Quenching Water of Blast Furnace Power Generation System
128.The Function Analysis and Design of Alien Shape Stone Multi-Function NC Machining Center
129.An Optimization Method for Fault Recognition of Rolling Bearing Based on Wavelet Neural Networks
130.Dynamic Modelling and Its Analysis of the Rigid-Flexible Coupled Linkage System with Second-Order Effects
131.Dynamic Simulation and Fatigue Vibration Analysis of the High Speed Bearing for Wind Turbine Gearbox
132.Feasibility Study and Simulation of B Pillar Made of Q&P Steel
133.Study on Electrostatic-Structural Coupling Characteristic of Microcantilever
134.Study on the Impact Resistance of Micromachined Gyroscope Spring Beams
135.The Design of Multi-Function Detection System ofAerial Working Platform Safety Lock
136.A Comparative Simulation Study of Evolutional Wavelet Based Denoising Algorithms
137.Research on Time-Different Ultrasonic Flowmeter Based on Cross Correlation Theory
138.The Application of Adaptive Algorithm on Automobile Sunroof Control System
139.Parameters Research and Improvement of Ant Colony Algorithm
140.Welding Mechanism of Aluminum Alloy under the Emergent Condition of Unprotected Gas
141.Research on Remanufacture Technology by Iron Alloy Plating Method
第七届工程机械与车辆工程新进展国际学术会议(ICACMVE'2019)
2011工程机械与车辆工程新进展国际学术会议论文集内容简介